How to buy a solar street light without over- or under-sizing it

Most solar street light projects fail on two numbers: the output was set from a catalogue page instead of the road, or the battery was sized for an average night instead of the worst week. This guide walks the five decisions in the order a project actually takes them, and points to the product data for each range.

1. Survey the site before choosing hardware

Four measurements decide more than any datasheet:

  • Mounting height. The height fixes the area one luminaire can light and the level of glare it creates.
  • Pole spacing. Spacing against height is what produces even light down the road; tight spacing allows a lower-power fixture.
  • Solar window. The panel needs an unshaded window at the right tilt; a partly shaded panel in winter loses far more than the shaded fraction.
  • Pole condition. On a retrofit the existing pole decides whether you can reuse it — diameter, material and wind-load rating all matter.

Write these down before a quotation is requested; they are the difference between a guess and a specification.

2. Set output from road class and spacing, not from a wish list

Work back from the target maintained illuminance for the road class. A residential lane, a collector road and a highway interchange carry different targets, and the target plus the spacing fixes the required lumen output and the optical distribution.

  • Wider spacing and taller poles push you toward higher output and narrower optics.
  • Pedestrian and campus paths are usually better served by lower output at tighter spacing, which also reduces light trespass.
  • Where the brief demands a specific uniformity figure, ask for a DIALux simulation rather than comparing lumen numbers.

3. Size autonomy before comparing prices

Autonomy is the number of consecutive low-sun days the light must keep running. It is set by the site's worst month, not its annual average, and it drives battery capacity more than any other input.

  • Ask every supplier for the design autonomy in days and the assumed peak sun hours.
  • Ask what the dimming profile is across the night: full output at dusk with a reduced level after midnight substantially lowers daily energy demand.
  • Check where the battery sits and how it is serviced; a battery that needs a crane to replace is cheap to buy and expensive to own.

E-Able Power publishes the integrated architecture behind each range — panel, LiFePO4 battery, MPPT controller and LED in one housing on the All-in-One range, and a separate panel and lamp body on All-in-Two.

4. Match the range to the road, then to the budget

  • All-in-One — one housing; fastest to install, best where theft resistance and simple logistics matter (village roads, parks, walkways).
  • All-in-Two — two pieces; the panel angle can be tuned on the pole, which helps at awkward sites.
  • Split — panel, lamp and battery specified separately; suits municipal and highway work where components are tendered and serviced separately.
  • Solar & Wind Hybrid — adds wind generation for low-sun or coastal sites.
  • High Mast — airports, seaports and stadiums, where the fixture is mounted well above the surface.
  • Bollards and post tops — footpaths, parks and facades rather than carriageways.

5. What to send so the quotation is a specification

Six inputs turn a price into a design: road type and width, target illuminance or the reference standard, mounting height and spacing, hours of operation per night, required autonomy in days, and the site location or latitude. Add the pole drawing if one exists.

Send those six and the layout, and the answer comes back as a system specification with a simulation, not a catalogue number.

Common buying mistakes

  • Comparing lumen output across fixtures with different optics — the distribution matters as much as the number.
  • Sizing the battery on the annual average sun hours instead of the worst month.
  • Buying on price per watt without checking the warranty terms and what is covered.
  • Forgetting the maintenance route: who replaces the battery, and with what access.

Frequently asked questions

How many watts do I need for a village road?

It depends on width, spacing and the target level. Give the road width and pole spacing and the output follows; a fixture chosen from wattage alone usually ends up either over-lit or under-lit on the ground.

Can the panel be mounted separately from the light?

Yes — that is what the All-in-Two and Split ranges are for. Separating them lets you orient the panel toward the sun while the lamp follows the road.

Is a battery replacement part of normal service?

Yes. Ask for the expected service interval and how the battery is accessed; the answer tells you more about lifetime cost than the purchase price.